Český manuál k dálkovému ovládání Rotel RR-1050

Dotazy a žádosti o radu co nakoupit, vylepšit, změnit ve vašich sestavách, ...
Odpovědět
Korina33
Příspěvky: 15
Registrován: 01 led 2020 22:24
Kontaktovat uživatele:

Český manuál k dálkovému ovládání Rotel RR-1050

Příspěvek od Korina33 »

Dobrý den, nemá někdo český manuál k dálkovému ovládání Rotel RR-1050?


Korina33
Příspěvky: 15
Registrován: 01 led 2020 22:24
Kontaktovat uživatele:

Re: Český manuál k dálkovému ovládání Rotel RR-1050

Příspěvek od Korina33 »

Bohužel není tam úplně jasné jak ho naprogramovat...!

Uživatelský avatar
harmasan
Příspěvky: 16
Registrován: 27 říj 2019 13:48
Kontaktovat uživatele:
Vybavení

Re: Český manuál k dálkovému ovládání Rotel RR-1050

Příspěvek od harmasan »

Toto je cast z anglickeho manualu. Daj si to do prekladaca a isto sa z toho vysomaris.
Programming
The RR-1050 replaces up to nine remote controls, one for
each of the DEVICE buttons. The AUD DEVICE/INPUT
button of the RR-1050 is pre-programmed with control
codes for Rotel audio/video receivers or surround sound
processors. The V1 button is pre-programmed to operate
Rotel DVD players. The other DEVICE/INPUT buttons (CD,
TUN, TAPE and V2 - V5) are unprogrammed. Any button in any device set can be reprogrammed
with new IR signals. Additional programming options such as special macro programming, clearing memorized commands, cloning commands from one RR-1050
to another and resetting the RR-1050 are described later
in this section.
Learning Mode
To teach the RR-1050 the commands from one of your other
remote controls, place the two remote controls end to end
as shown in the illustration at the front of this manual. The
IR signals sent by the other remote must be aimed at the IR
emitter/sensor of the RR-1050.
There are two different sets of steps used when programming the RR-1050. One set is used to program the COMMAND buttons. A shorter set of steps is used to program
DEVICE/INPUT buttons to select an input source for the
device being operated.
To program a COMMAND button:
1. Press the LEARN button on the RR-1050. The
LEARN indicator blinks in the display.
2. Press the DEVICE/INPUT button of the RR-1050 to
select the device (CD, V2, etc.) whose command set
you want to program. The name of that device appears in the display.
3. Press the COMMAND button that you want to
program (4, CH UP/DOWN, etc.). The label for that
COMMAND button appears in the display and the
LEARN indicator stops blinking.
4. Press and hold the corresponding button on the original remote until the display shows “OK!” indicating
that the command has been learned.
The LEARN indictor resumes blinking once the command
has been learned. Repeat Steps 3 and 4 for each COMMAND button you wish to program in that command set –
for example, for each transport and track selection function on your CD player.
To program a DEVICE/INPUT button or the EXT
button to select an input for the device being
operated:
1. Press the LEARN button on the RR-1050. The
LEARN indicator blinks in the display.
2. Press and hold the DEVICE/INPUT button you want to
program until the LEARN indicator stops blinking The
label for that device appears in the display.
3. Press and hold the corresponding input selection button on the original remote until the display shows
“OK!” indicating that the command has been learned.
Repeat Steps 2 and 3 for each DEVICE/INPUT button you
wish to program for input source selection.
NOTE: The AUD INPUT/DEVICE button cannot be programmed for input source selection.
While programming the RR-1050:
If the display shows an ERROR message, the
command was not successfully learned. Try again.
If the display shows a NO DATA message, no
signal was received from the original remote. Adjust the
position of the two remote controls and try again.
The RR-1050 exits the LEARN mode following 15 seconds
without pressing any buttons.
Multi-Step COMMAND Button Learning
The five buttons labeled SCAN, PTY, P-TUN, TP, TA
provide a special option – the ability to learn up to three
different commands on a single button. During operation,
the first command is sent when the button is pressed once,
the second command is sent the next time the button is
pressed, and the third command is sent the third time the
button is pressed.
Nie je za co.

Odpovědět

Kdo je online

Uživatelé prohlížející si toto fórum: Žádní registrovaní uživatelé a 147 hostů